| Freq. Response | 10 Hz to 80 kHz ± 0.5 dB (192 kHz sample rate, re 1 kHz) |
| THD + Noise | 0.005% max (1 kHz, 22 Hz–22 kHz BW, trim @20, fader @ 0, -10 dBu in) |
| Equivalent Input Noise | -131 dBV (-129 dBu) max (A-weighting, 76 dB gain, 150 ohm source impedance) |
| Processing Engine | Highly extensible, full FPGA-based audio processing, 3 FPGAs
Six-way ARM multiprocessor system. 64-bit audio processing precision |
| Audio Over Ethernet | Dante, 32 channels in, 32 channels out. AES67 compatible
1 Gb/s Ethernet, 2 ports, transformer-balanced |
| Inputs | Mic/Line inputs: 16 total, all fully featured; 6 on full-size XLR, 2 on TA3, 8 on TA5
Mic-level inputs: (XLR, TA3, TA5): Class-A, discrete differential long-tail pair, 4k ohm input impedance
Line-level inputs: (XLR, TA3, TA5): active-balanced, 4k ohm input impedance
AES3 or AES42 available on XLR inputs 1 and 6. AES42: +10 V, 250 mA available, type-1, auto-ASRC
Rtn A, B, C (3.5 mm/10-pin): unbalanced 2-channel, 4k ohm input impedance
Com Rtn 1,2 (TA3, 3.5mm) balanced, 1-channel, 8k ohm input impedance
External Slate Mic (TA5): balanced, 8k ohm input impedance, menu-selectable 12 V phantom |
| Maximum Input Level | Mic: +8 dBu (2.0 Vrms)
Line: +28 dBu (19.5 Vrms)
Rtn A, B, C: +18 dBu (6.2 Vrms)
Com Rtn 1, 2: +24 dBu (12.3 Vrms)
External Slate Mic: +12 dBu (3.2 Vrms) |
| High-Pass Filters | Adjustable 40 Hz to 320 Hz, 18 dB/oct
1st stage analog(before preamp), 2nd stage digitalLimiters
Limiters available at all channels, buses, headphones, for all sample rates
Analog first stage, all subsequent stages digital
Attack time: 1 ms. Release time: adjustable, 50 ms to 1000 ms
Threshold: adjustable, -2 dBFS to -12 dBFS. Selectable knee: hard or soft
Selectable ratio: inf:1, 20:1 |
| Delay | Channel Adjustable 0-50 ms. Output Adjustable 0-500 ms |
| Maximum Gain | Trim stage (mic input): 76 dB
Trim stage (line input): 36 dB
Fader stage: 16 dB. Bus stage: 16 dB
Headphone stage: 20 dB
Mic-to-Line: 108 dB
Mic-to-Headphone: 112 dB |
| Outputs | XLR (L, R) active-balanced, 250/3.2k/120 ohms (mic/-10/line)
Hirose 10-pin (L, R) active-balanced, 250/3.2k/120 ohms (mic/-10/line)
TA3 (X1-X6) active-balanced, 250/3.2k/120 ohms (mic/-10/line)
3.5mm (X7, X8): unbalanced, stereo, 1.8k ohms |
| Headphone Outputs | ¼”, 3.5 mm
TA5 (along with mic input pins) for single connection to headset + mic
High output, 4 ohm output impedance, 400 mW + 400 mW at each connector, all individually driven
Compatible with headphones of any impedance |
| Maximum Output Level(all into 10k load) | Line: +20 dBu (7.8 Vrms)
“-10”: +6 dBu (1.5 Vrms)
Mic: -20 dBu (0.078 Vrms)
X7/X8 Out: +6 dBu (1.5 Vrms)
Headphone outputs (¼”, TA-5, X9/X10): +14 dBu (4.0 Vrms) |
| A/D converters | 32-bit, 120 dB, A-weighted dynamic range typical
Sampling rates 44.1 kHz, 47.952 kHz, 48 kHz, 48.048 kHz, 88.2 kHz, 96 kHz, 192 kHz |
| Digital Outputs | AES3 transformer-balanced, in pairs; 1-2 (XLR-L), 3-4 (XLR-R), 5-8 (Hirose 10-pin A)
110 ohm, 2 V p-p, AES and S/PDIF compatible |
| Recording | Internal 256 GB SSD
Two removable SD Cards
Simultaneous recording to internal SSD and the two SD cards
exFAT formatting. 36 tracks (32 iso channels, 4 buses)
Broadcast WAV monophonic and polyphonic file format
64-bit WAV (RF64) monophonic and polyphonic; support for files > 4 GB |
| USB | USB-C (USB 3.1 type 1) for file transfer of internal SSD, both SD Cards
USB-A host for keyboard, external controller, external USB hubs supported for connecting multiple devices |
| Wireless | Built-in Bluetooth v5.0 BLE (not supported with rev 1.0 release of SD-Remote) |
| Timecode and Sync | Modes Supported: Off, Rec Run, Free Run, 24h Run, External, including External Auto-Record and Continuous modes
Frame Rates: 23.98, 24, 25, 29.97 DF, 29.97 ND, 30 DF, 30 ND
Sample/Timecode Accuracy: 0.1 ppm (0.25 frames per 24 hours)
Timecode Input: 20k ohm impedance, 0.3 V - 3.0 V p-p (–17 dBu - +3 dBu)
Timecode Output: 75 ohm impedance, 5 V p-p (+12 dBu)
Word Clock Input: 10k/75 ohm selectable impedance, 1-5 V p-p input sensitivity
Word Clock Output: 75 ohm impedance, 5 V p-p output, at SR |
| Remote Control | USB MIDI Control - 3rd party fader controllers
SD-Remote Android app
USB Keyboard
External Timecode Record Trigger |
| LCD | 320x240, Transflective, excellent sunlight visibility
Larger touchscreen display available via USB-connected SD-Remote app |
| Power | External: dual 10-18 V inputs on locking TA4 connectors, pin-4 = (+), pin-1 = (-)
Dual rear-mount Sony-style L-mount batteries with chargers
Idle Current Draw: 875 mA @ 12 V (10.5 W)
Intelligent power-down of unused mic preamps and other internal circuits |
| Environmental | Operating: -20° C to 60° C, 0 to 90% relative humidity (non-condensing)
Storage: -40° C to 85° C |
| Dimensions (H x W x D) | 5.1 cm x 32 cm x 20.5 cm ( 2 in x 12.6 in x 8.1 in) |
| Weight | 5.8 lbs (2.63 kg) unpackaged, without batteries |
